|
Scattering parameters or S-parameters (the elements of a scattering matrix or S-matrix) describe the electrical behavior of linear electrical networks when undergoing various steady state stimuli by electrical signals. The parameters are useful for electrical engineering, electronics engineering, and communication systems design, and especially for microwave engineering. The S-parameters are members of a family of similar parameters, other examples being: Y-parameters,〔Pozar, David M. (2005); ''Microwave Engineering, Third Edition'' (Intl. Ed.); John Wiley & Sons, Inc.; pp. 170-174. ISBN 0-471-44878-8.〕 Z-parameters,〔Pozar, David M. (2005) (op. cit.); pp. 170-174.〕 H-parameters, T-parameters or ABCD-parameters.〔Pozar, David M. (2005) (op. cit.); pp. 183-186.〕〔Morton, A. H. (1985); '' Advanced Electrical Engineering''; Pitman Publishing Ltd.; pp. 33-72. ISBN 0-273-40172-6.〕 They differ from these, in the sense that ''S-parameters'' do not use open or short circuit conditions to characterize a linear electrical network; instead, matched loads are used. These terminations are much easier to use at high signal frequencies than open-circuit and short-circuit terminations. Moreover, the quantities are measured in terms of power. Many electrical properties of networks of components (inductors, capacitors, resistors) may be expressed using S-parameters, such as gain, return loss, voltage standing wave ratio (VSWR), reflection coefficient and amplifier stability. The term 'scattering' is more common to optical engineering than RF engineering, referring to the effect observed when a plane electromagnetic wave is incident on an obstruction or passes across dissimilar dielectric media. In the context of S-parameters, scattering refers to the way in which the traveling currents and voltages in a transmission line are affected when they meet a discontinuity caused by the insertion of a network into the transmission line. This is equivalent to the wave meeting an impedance differing from the line's characteristic impedance. Although applicable at any frequency, S-parameters are mostly used for networks operating at radio frequency (RF) and microwave frequencies where signal power and energy considerations are more easily quantified than currents and voltages. S-parameters change with the measurement frequency, so frequency must be specified for any S-parameter measurements stated, in addition to the characteristic impedance or system impedance. S-parameters are readily represented in matrix form and obey the rules of matrix algebra. ==Background== The first published description of S-parameters was in the thesis of Vitold Belevitch in 1945.〔Belevitch, Vitold ("Summary of the history of circuit theory" ), ''Proceedings of the IRE'', vol.50, iss.5, pp. 848–855, May 1962. Vandewalle, Joos ("In memoriam – Vitold Belevitch" ), ''International Journal of Circuit Theory and Applications'', vol.28, iss.5, pp. 429–430, September/October 2000.〕 The name used by Belevitch was ''repartition matrix'' and limited consideration to lumped-element networks. The term ''scattering matrix'' was used by physicist and engineer Robert Henry Dicke in 1947 who independently developed the idea during wartime work on radar.〔Valkenburg, Mac Elwyn Van ''Circuit Theory: Foundations and Classical Contributions'', p.334, Stroudsburg, Pennsylvania: Dowden, Hutchinson & Ross, 1974 ISBN 0-87933-084-8.〕〔(J. Appl. Phys. 18, 873 (1947); doi: 10.1063/1.1697561 A Computational Method Applicable to Microwave Networks R. H. Dicke )〕 The technique was popularized in the 1960s by Kaneyuki Kurokawa In the S-parameter approach, an electrical network is regarded as a 'black box' containing various interconnected basic electrical circuit components or lumped elements such as resistors, capacitors, inductors and transistors, which interacts with other circuits through ''ports''. The network is characterized by a square matrix of complex numbers called its S-parameter matrix, which can be used to calculate its response to signals applied to the ports. For the S-parameter definition, it is understood that a network may contain any components provided that the entire network behaves linearly with incident small signals. It may also include many typical communication system components or 'blocks' such as amplifiers, attenuators, filters, couplers and equalizers provided they are also operating under linear and defined conditions. An electrical network to be described by S-parameters may have any number of ports. Ports are the points at which electrical signals either enter or exit the network. Ports are usually pairs of terminals with the requirement that the current into one terminal is equal to the current leaving the other.〔Pozar, David M. (2005) (op. cit.); p. 170.〕〔Morton, A. H. (1985) (op. cit.); p. 33.〕 S-parameters are used at frequencies where the ports are often coaxial or waveguide connections. The S-parameter matrix describing an ''N''-port network will be square of dimension ''N'' and will therefore contain elements. At the test frequency each element or S-parameter is represented by a unitless complex number that represents magnitude and angle, i.e. amplitude and phase. The complex number may either be expressed in rectangular form or, more commonly, in polar form. The S-parameter magnitude may be expressed in linear form or logarithmic form. When expressed in logarithmic form, magnitude has the "dimensionless unit" of decibels. The S-parameter angle is most frequently expressed in degrees but occasionally in radians. Any S-parameter may be displayed graphically on a polar diagram by a dot for one frequency or a locus for a range of frequencies. If it applies to one port only (being of the form ), it may be displayed on an impedance or admittance Smith Chart normalised to the system impedance. The Smith Chart allows simple conversion between the parameter, equivalent to the voltage reflection coefficient and the associated (normalised) impedance (or admittance) 'seen' at that port. The following information must be defined when specifying a set of S-parameters: #The frequency #The characteristic impedance (often 50 Ω) #The allocation of port numbers #Conditions which may affect the network, such as temperature, control voltage, and bias current, where applicable. 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「scattering parameters」の詳細全文を読む スポンサード リンク
|